Arcadyan ARC-1226-8i RAID Controller

Indicates whether the product contains a built‑in central processing unit (CPU) that can execute instructions without requiring an external processor module. A value of "Yes" means the device has such a CPU; "No" means it does not.

The highest theoretical speed at which a device can send or receive data, expressed in bits per second (bps) or its multiples such as kbps, mbps, gbps, etc. It represents the upper bound of throughput under optimal conditions and is useful for comparing performance across devices and interfaces.

The vertical dimension of a product measured from its lowest to highest point. It is expressed in a physical unit such as millimetres, centimetres or inches and applies to any item where height is relevant, including books, electronics, furniture and other objects.

List of physical or logical interfaces that allow communication between a host device and other components, such as USB, PCI Express, SATA, M.2, Ethernet, Thunderbolt, or similar standards.

The physical or logical interface used by a device to connect with other components, such as USB, PCI Express, SATA, Ethernet, Thunderbolt, DisplayPort, or similar standards. It indicates the technology that enables data transfer and power delivery between the product and its peripherals.

The total amount of internal memory available in a device, expressed as a data size such as megabytes (MB) or gigabytes (GB). It indicates how much information the component can hold for active processes and affects multitasking performance.

The type of memory physically installed inside a device, such as DDR4 SDRAM, LPDDR3, or other RAM variants. It indicates the architecture and generation of the internal memory modules that the product uses or supports.

Indicates whether the product can operate in Just‑Bigger‑On‑Disk (JBOD) mode, allowing multiple drives to be treated as a single logical volume without RAID configuration.

List of Linux operating systems that the product can run or support, including specific versions and architectures when relevant. Each value represents a distinct Linux distribution or kernel version supported by the hardware or software.

Indicates whether the product is designed to fit in low‑profile or slim form factors, such as low‑height graphics cards or compact components that require reduced vertical clearance. A value of "Yes" means the item can be installed in a low‑profile chassis or slot; "No" indicates it requires standard or higher clearance.

The maximum operating frequency of a memory module, expressed in hertz (Hz). It indicates how many cycles per second the RAM can perform and is typically reported as MHz or GHz. This value helps users compare performance potential across different memory types and system configurations.

The range of relative humidity (in percentage) within which the product is designed to operate reliably. Values are expressed as a minimum–maximum interval such as "20 - 80 %" and indicate the acceptable environmental moisture level for optimal performance.

A list of operating system names and versions that the product can run or support beyond its primary OS, including both commercial and open‑source distributions. Each value represents a distinct OS that is compatible with the hardware or software.

The processor family identifies the group or series of CPU models that share a common architecture, design, and performance characteristics. It helps users compare processors across brands and generations by indicating the underlying technology used in the chip.

The fundamental operating frequency of a processor, expressed in hertz (Hz). It indicates the speed at which the CPU runs under normal conditions and is typically reported in gigahertz (GHz) or megahertz (MHz). This value helps users compare performance potential across different models.

A comma‑separated list that specifies the RAID configurations supported by a storage controller or device. Each entry can be a numeric level (e.g., 0, 1, 5, 10) or a special label such as JBOD. This attribute indicates which disk arrangements the system can manage.

A comma‑separated list of RAID levels that a storage device or controller can support, such as 0, 1, 5, 10, JBOD, and other proprietary configurations. Each value represents a distinct RAID mode the system is capable of creating or managing.

A list of operating systems that the server product can run or support, including specific versions and architectures when relevant. Each value represents a distinct OS compatible with the hardware.

Indicates whether a product includes an internal or external solid‑state drive (SSD) interface or component, allowing the device to use SSDs for storage. The value is typically "Yes" if the product supports SSDs and "No" otherwise.

The range of relative humidity (expressed as a percentage) within which the storage device is designed to operate reliably. Values are given as a minimum–maximum interval such as "10 - 90 %" and indicate the acceptable environmental moisture level for optimal performance.

List of physical or logical interfaces that allow an internal storage drive to communicate with the system, such as SATA, M.2 PCIe, U.2, SAS, NVMe, or other standard connections.

The horizontal measurement of a product, expressed in a linear unit such as millimetres or inches. It indicates how wide the item is from one side to the other and is used for sizing, fitting, and compatibility purposes.