Dell N2224PX-ON Power over Ethernet (PoE) Switch

Indicates whether the product supports an Access Control List (ACL) feature, allowing administrators to define rules that permit or deny network traffic based on criteria such as IP address, port number, or protocol.

The authentication mechanisms supported by a network device or access control system. Common values include RADIUS, IEEE 802.1x, HWTACACS+, AAA, and combinations of these protocols. The attribute lists all enabled methods, separated by commas.

Indicates the total count of physical RJ‑45 Ethernet connectors available on a device for wired network connectivity. The value is an integer representing how many separate ports can be used to connect Ethernet cables.

The colour or combination of colours that a product is available in, expressed as common names such as "Black", "Silver" or comma‑separated lists like "Black, White". It indicates the visual appearance of the item for consumers.

The linear measurement of an object from front to back or top to bottom, expressed in a physical unit such as millimeters, centimeters, inches, etc. It indicates how deep the item is and can be used for fitting, compatibility, or spatial planning.

Specifies the physical configuration or design of a product, such as ATX, Micro‑ATX, Mini‑ITX, tower, case with cover, etc. It describes how the device is built and what mounting or expansion options it supports.

The maximum number of packets a device can forward per second, expressed in megapackets per second (Mpps) or similar units. It indicates the throughput capability of networking hardware such as switches and routers under optimal conditions.

The vertical dimension of a product measured from its lowest to highest point. It is expressed in a physical unit such as millimetres, centimetres or inches and applies to any item where height is relevant, including books, electronics, furniture and other objects.

The total number of Small Form-factor Pluggable (SFP) transceiver modules that are physically installed in a networking device such as a switch, router or hub. This count indicates how many SFP slots are populated and can be used for fiber or copper uplinks.

The total count of unique MAC addresses that the device can store in its forwarding table. This value indicates how many devices can be simultaneously connected before the switch must start discarding or aging out older entries.

The total count of manually configured static routing entries present in a networking device such as a router or switch. It indicates how many distinct destination networks are explicitly defined by the administrator, independent of dynamic routing protocols.

The range of relative humidity (in percentage) within which the product is designed to operate reliably. Values are expressed as a minimum–maximum interval such as "20 - 80 %" and indicate the acceptable environmental moisture level for optimal performance.

The range of temperatures in which a product can safely operate without risk of damage or performance degradation. Values are expressed in degrees Celsius (°C) and may represent a single temperature, a minimum–maximum interval, or an average operating point.

Indicates whether a product is designed to be mounted in a rack system. The value can be "Yes" or "No", or it may specify the height occupied by the device using rack units (U) such as "1U", "2U", or a numeric measurement with unit, e.g., "61.25 mm".

Indica los estándares o velocidades que soportan los puertos RJ‑45 presentes en el producto, como Fast Ethernet (10/100 Mbps), Gigabit Ethernet (1 Gbps) o 10 Gigabit Ethernet. Cada valor describe una capacidad específica del conector y permite comparar la compatibilidad de red entre dispositivos.

The range of relative humidity (expressed as a percentage) within which the storage device is designed to operate reliably. Values are given as a minimum–maximum interval such as "10 - 90 %" and indicate the acceptable environmental moisture level for optimal performance.

The range of temperatures in which a device can safely operate without risk of damage or performance degradation. Values are expressed in degrees Celsius (°C) and may represent a single temperature, a minimum–maximum interval, or an average operating point.

The network layer(s) that a device can operate at, expressed as a string such as "L2", "L3" or combinations like "L2/L3". This attribute indicates the protocol stack level supported by the hardware or firmware.

The classification of a network switch based on its management capabilities, such as Managed or Unmanaged. This attribute indicates whether the device can be configured and monitored remotely (Managed) or operates with fixed settings without remote configuration (Unmanaged). It helps users choose a switch that matches their networking expertise and control requirements.

The maximum data transfer rate that the device can handle, expressed as a numeric value with an appropriate unit such as Gbit/s or Mbit/s. This attribute indicates how quickly data can be transmitted through the device and helps users compare networking performance across products.

The horizontal measurement of a product, expressed in a linear unit such as millimetres or inches. It indicates how wide the item is from one side to the other and is used for sizing, fitting, and compatibility purposes.