D-Link DGS-1210-10

Indicates whether the product supports 10 Gigabit Ethernet (10 GbE) connectivity, either through dedicated 10 GbE ports or via SFP+ modules that enable 10 GbE operation.

The frequency of the alternating current supplied to the device, expressed in hertz (Hz). It indicates the acceptable operating range for the electrical mains that powers the product.

The alternating current voltage range that the product accepts from its power source, expressed in volts (V). It indicates the minimum and maximum supply voltages compatible with the device.

Indicates whether the product includes an ARP inspection feature, allowing the device to monitor and filter Address Resolution Protocol traffic for security or performance purposes.

Indicates whether the device can automatically detect and configure MDI or MDI‑X connections for network cables, simplifying cable management and reducing manual setup.

Indicates whether the device automatically negotiates link parameters such as speed, duplex mode and flow control with a connected partner, ensuring optimal communication settings without manual configuration.

The American Wire Gauge (AWG) size of a conductor, expressed as an integer that indicates the wire’s diameter and cross‑sectional area. Lower numbers represent thicker wires with higher current capacity; higher numbers indicate thinner conductors suitable for lower currents or signal applications.

Indicates the total count of physical RJ‑45 Ethernet connectors available on a device for wired network connectivity. The value is an integer representing how many separate ports can be used to connect Ethernet cables.

The linear distance that a cable covers, expressed with a length unit such as meters, centimeters or inches. It represents the total usable length of the cable for connecting devices.

The type of electromagnetic shielding applied to a cable or its connector, indicating whether the cable is unshielded, shielded with foil, braided, or uses a combination such as UTP, FTP, S‑FTP, or other common configurations. This attribute helps users identify compatibility with devices that require specific shielding levels.

The category or technology of a cable, such as Cat5e, Cat6, HDMI, USB, SATA, fiber optic, or other transmission types. It identifies the primary function and compatibility of the cable with devices and systems.

A list of the cable types that are supplied with the product, such as USB, HDMI, VGA, DisplayPort, LAN (RJ‑45), SATA, audio or other relevant connectors.

A list of official certifications or compliance marks that the product has received from regulatory bodies, safety organizations, or industry standards groups. Each entry represents a distinct certification such as CE, FCC, RoHS, UL, or WEEE, and may include additional details like version numbers or specific test reports.

The colour or combination of colours that a product is available in, expressed as common names such as "Black", "Silver" or comma‑separated lists like "Black, White". It indicates the visual appearance of the item for consumers.

The network and data interface technologies supported by the product, such as Wired, Wireless, USB, Bluetooth, or combinations thereof. Each value represents a distinct technology that can be used for communication or power delivery.

The physical interface or port located at the first end of a cable or device, such as USB‑A, HDMI, RJ‑45, DisplayPort, Lightning, or other standard connectors. It identifies the shape, pin count and electrical characteristics that determine compatibility with cables, adapters or other components.

The metal coating applied to the contacts of a connector, such as gold, nickel, copper or chrome. It provides corrosion resistance, conductivity and durability for the electrical connections.

The linear measurement of an object from front to back or top to bottom, expressed in a physical unit such as millimeters, centimeters, inches, etc. It indicates how deep the item is and can be used for fitting, compatibility, or spatial planning.

Indicates whether a device includes hardware or firmware that can manage the flow of data on its interfaces, such as enabling or disabling automatic pause frames, handling congestion, or providing other traffic‑control mechanisms. A value of "Yes" means the feature is present and can be configured; "No" indicates it is not available.

Specifies the physical configuration or design of a product, such as ATX, Micro‑ATX, Mini‑ITX, tower, case with cover, etc. It describes how the device is built and what mounting or expansion options it supports.

The maximum number of packets a device can forward per second, expressed in megapackets per second (Mpps) or similar units. It indicates the throughput capability of networking hardware such as switches and routers under optimal conditions.

Indicates whether a device can transmit and receive data simultaneously on two channels, allowing bidirectional communication without delay. A value of "Yes" means the device supports full‑duplex operation; a value of "No" indicates it operates only in half‑duplex mode.

The amount of thermal energy a product can dissipate, expressed in a standard unit such as BTU per hour or watts. It indicates the cooling requirement and helps compare how much heat the device generates during operation.

The vertical dimension of a product measured from its lowest to highest point. It is expressed in a physical unit such as millimetres, centimetres or inches and applies to any item where height is relevant, including books, electronics, furniture and other objects.

The range of electrical voltage that a device can safely accept from its power source, expressed in volts (V). It specifies the minimum and maximum supply voltages compatible with the product, covering both AC and DC inputs where applicable.

The outer jacket material is the substance that forms the protective sheath or covering of a product, such as cables, hoses, or enclosures. It determines durability, fire‑resistance, and suitability for specific environments. Common materials include PVC, LSZH, TPE, nylon, ABS, and their combinations.

The largest Ethernet frame size (in bytes) that the device can transmit or receive without fragmentation. This value determines the maximum payload that can be sent in a single network packet, which can improve throughput for high‑bandwidth applications.

Indicates whether the device can combine multiple network connections into a single logical link to increase bandwidth or provide redundancy.

Indicates whether the device includes loop protection to prevent network loops that can cause broadcast storms and disrupt traffic.

Indicates whether the device supports filtering network traffic based on MAC addresses. When enabled, the device can allow or block communication for specific devices identified by their MAC address.

The total count of unique MAC addresses that the device can store in its forwarding table. This value indicates how many devices can be simultaneously connected before the switch must start discarding or aging out older entries.

Indicates whether the device can send or receive IP multicast traffic, allowing it to participate in group communications such as streaming media, IPTV, and certain network protocols that rely on multicast distribution.

A list of the networking protocols and standards that a device can support or comply with, such as IEEE 802.11 variants for wireless, IEEE 802.3 for Ethernet, or other relevant networking specifications. The values are typically separated by commas and may include both technical identifiers and consumer‑friendly labels.

The range of relative humidity (in percentage) within which the product is designed to operate reliably. Values are expressed as a minimum–maximum interval such as "20 - 80 %" and indicate the acceptable environmental moisture level for optimal performance.

The linear measurement from front to back or top to bottom of a product’s packaging, expressed in a physical unit such as millimeters, centimeters, inches, etc. It indicates how deep the packaged item is and can be used for fitting, compatibility, or spatial planning.

The vertical dimension of a product’s packaging measured from its lowest to highest point. It is expressed in a physical unit such as millimetres, centimetres or inches and helps customers assess how tall the package will be when stored or shipped.

The horizontal measurement of a product’s packaging, expressed in a linear unit such as millimetres or inches. It indicates how wide the package is from one side to the other and helps customers assess fit for storage, shipping, or display.

The amount of temporary storage that a device allocates in its internal memory for buffering data before processing or forwarding it. Expressed as a digital capacity (e.g., kilobytes, megabytes), this value indicates how much information the hardware can hold at once and influences performance when handling high‑throughput or bursty traffic.

The linear dimension of a pallet measured in a standard unit such as meters, centimeters or inches. It represents the overall length from one end to the other and is used to compare the size of pallets across different products and logistics contexts.

The horizontal measurement of a pallet, expressed in a linear unit such as millimetres or inches. It indicates how wide the pallet is from one side to the other and helps customers assess fit for storage, shipping, or display.

Indicates whether the device supports port mirroring, a feature that allows one or more ports to copy traffic from another port for monitoring or analysis purposes.

The type of connector used to supply power to the device, such as AC‑in jack, DC‑in jack, USB Type‑C, SATA Power, or PCIe power connectors. It indicates the physical interface that delivers electrical energy to the product.

Indicates whether a product is designed to be mounted in a rack system. The value can be "Yes" or "No", or it may specify the height occupied by the device using rack units (U) such as "1U", "2U", or a numeric measurement with unit, e.g., "61.25 mm".

Indica los estándares o velocidades que soportan los puertos RJ‑45 presentes en el producto, como Fast Ethernet (10/100 Mbps), Gigabit Ethernet (1 Gbps) o 10 Gigabit Ethernet. Cada valor describe una capacidad específica del conector y permite comparar la compatibilidad de red entre dispositivos.

Indicates whether the product is manufactured in accordance with the RoHS (Restriction of Hazardous Substances) directive, which limits the use of certain hazardous materials in electrical and electronic equipment.

A list of safety and regulatory certifications that a product complies with, such as CE, UL, FCC, or other regional standards.

The functional configuration of a scanner, indicating how documents are fed into the device. Common types include flatbed scanners with automatic document feeders (ADF), sheet‑fed scanners, single‑pass or dual‑pass ADFs, and specialized modes such as 1D/2D barcode readers. This attribute helps users understand whether the scanner can handle single pages, multiple pages automatically, or specific scanning formats.

The total count of Small Form‑factor Pluggable (SFP) ports available on a networking device, such as switches or routers. Each port can accept an SFP transceiver module for fiber or copper connections, allowing the device to support additional network interfaces.

Indicates whether the device implements the Spanning Tree Protocol (STP), a network protocol that prevents loops in Ethernet topologies by dynamically blocking and forwarding paths to maintain a loop‑free logical topology.

The range of relative humidity (expressed as a percentage) within which the storage device is designed to operate reliably. Values are given as a minimum–maximum interval such as "10 - 90 %" and indicate the acceptable environmental moisture level for optimal performance.

Indicates whether the device can temporarily store data packets before forwarding them, allowing traffic management even when the destination is not immediately available. A positive value means the device can buffer and later deliver packets reliably.

The classification of a network switch based on its management capabilities, such as Managed or Unmanaged. This attribute indicates whether the device can be configured and monitored remotely (Managed) or operates with fixed settings without remote configuration (Unmanaged). It helps users choose a switch that matches their networking expertise and control requirements.

The maximum data transfer rate that the device can handle, expressed as a numeric value with an appropriate unit such as Gbit/s or Mbit/s. This attribute indicates how quickly data can be transmitted through the device and helps users compare networking performance across products.

The general category or style of the product, such as laptop, printer cartridge, or cooling fan. It helps buyers quickly identify the nature of the item and compare similar products.

Indicates whether the product can be configured and monitored through a web interface accessible via a browser, allowing remote administration over a local or internet connection.

The mass of the product expressed in a standard unit such as grams or kilograms. It represents how heavy the item is and can be used for shipping calculations, handling instructions, or consumer information.

The horizontal measurement of a product, expressed in a linear unit such as millimetres or inches. It indicates how wide the item is from one side to the other and is used for sizing, fitting, and compatibility purposes.